Dual Drive Controller With LCD Display 48V60V72V50A for Electric Scooter Acces
Description : Voltage: DC48V-72V Current limit: 45A/50A Undervoltage: 41/51V Power: 1500W/2000W/2500W/3000W/3500W Size:152*82*45MM 48-60V 45A: the 45A is for each one controller,can use the motor voltage with 48v 52v 60v, power with 1500w 2000w 2500w 3000w; 60-72V 50A: the 50a is for each one controller,can use the motor voltage with 60v 72v, Power with 2500w 3000w 3500w. Appearance size and material: The product shell is ABS, and the LCD transparent window is imported high-hardness acrylic, the hardness value is equivalent to ten tempered glass. Function description: Power switch control, wheel diameter setting, idle automatic sleep time setting, backlight brightness setting, startup mode setting, driving mode setting, voltage level setting, controller current limit setting. 1. Display function: speed display, power indicator, fault prompt, total mileage, single mileage. 2. Control and setting functions All contents of the display screen. (full display within 1S after power-on) How to setting LCD display: P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P02: mileage unit, 0: KM; P03: Voltage level: 24V, 36V, 48V, default 36V; P04: sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; unit minute; P05: Power assist gear: 0: 3rd gear mode; P06: wheel diameter: unit, inch; accuracy: 0.1; P07: Speed measuring magnetic steel number: range: 1-100; P08: Speed limit: range 0-100km/h, 100 means no speed limit; 1. Communication state (controller control): the driving speed is maintained at the set value, 6 Error: ±1km/h; (both assist and handle speed limit) Note: The value here is based on kilometers. When the unit setting is converted from kilometers to miles, the speed value on the display interface will automatically convert to the correct mile value, but the speed limit value data set in this menu under the mile interface No conversion, inconsistent with the actual displayed mile speed limit value; P09: zero start, non-zero start setting, 0: zero start; 1: non-zero start; P10: Driving mode setting 0: Power-assisted drive (the amount of power output is determined by the power-assisted gear, and the handle is invalid at this time). 1 : Electric drive (driven by turning the handle, at this time the power assist gear is invalid). 2: Power assist drive and electric drive coexist at the same time (the electric drive is invalid in zero-start state). P11: Assist sensitivity setting 1-24 P12: Starting strength setting 0-5 P13: Power-assisted magnetic steel plate type setting 5, 8, 12 grains of magnetic steel three types P14: Controller current limit setting Default 12A Range: 1-20A P15: controller undervoltage value P17: Automatic cruise selection, 0 without automatic cruise, 1 with automatic cruise. P18: ABS brake strength selection, generally adjustable from 0 to 3 levels Fault code: Fault status Remarks 0. Normal state 1. Reserved 2. brake 3. Power sensor failure (riding sign) 4.6KM/H cruise 5. Real-time cruise is not realized here 6. Battery undervoltage 7. Motor failure 8. Handlebar failure 9. Controller failure 10. Communication reception failure 11. Communication sending failure 12. BMS communication failure 13. Headlight failure The LCD display shows ODO:Total mileage TRIP:Single mileage VOL:Digital voltage CUR:Digital current RM(requires battery protection board software support): Remaining mileage TIME:Running time ERRO:Fault code
30A 36V 48V KT Waterproof Controller For 1000W 1500W E-bike Brushless Motor
PAS (3pin waterproof plug). 1 to 4 cable(8 pins for throttle, e-bike, display). Connectors:.
Electric Bicycle 60V 2000W Controller 48V 1000W Sine Controller 48V 1500W 72V
Product parameters Color:Golden Condition: 100% brand newItem type: Motor Controller Material: Aluminium alloy Voltage:36V-48V-60V-64V-72V -84V Weight: .697g Power: 1000W-2000W Current limit:34A-40A What is a Three-mode controller? Quiet start(Except for special circumstances) strong power and power saving. The three-mode controller is a sine wave controller. It can operate in three modes, sine wave mode, square wave mode, and no hall mode (that is, it can be used without a hall sensor). The mode cannot be selected, the default is sine wave mode. When the hall sensor is damaged it will automatically switch to square wave mode. Runs no-Hall mode when no Hall sensors are connected. Suitable for in-wheel motors.Differential motor, etc. Tips: Applicable to a variety of motors, but only in-wheel motors with Hall sensors can use sine wave mode. When running other motors, it will automatically switch to square wave mode or no Hall mode. Installation Instructions Step 1. Connect wires 1, 2, 6, 8, 17. Step 2. Connect the No. 5 wire with the motor suspended. (Note: the motor needs to be in the overhang position for docking wire #5) Step 3. The motor will perform a forward/reverse state. (If there is a reversal you will need to disconnect the 5 wire and reconnect it) Wait 10 seconds in the forward state to complete learning. Step 4. Make the wiring connections according to the vehicle. Line Description 1. Power supply 2.Motor phase line 3.Anti-theft signal 4.Anti-theft power supply 5.Intelligent learning 6.Throttle 7.High level brake 8.Key switch 9. Dial gear three speed 10. Phase line speed measurement 11.One line pass 12. Differential motor special 13. Fixed speed cruise control 14.PAS 15.Low level brake 16.Reversing 17.Hall sensor 18.Hall speed measurement
48V-72V Electric Bike Sine Wave Split Intelligent Motor Speed Controller 1500W
Rated Power: 1500w. Do You Want to Experience a Smoother Ride?. It Has Low Noise and Stable Performance That Can Provide You with Strong Power. the Thicker Copper Wire Design Gives It Higher Inductance Accuracy, Making Your Electric Bike Start More Smoothly and Allowing You to Enjoy a More Comfortable Ride!
Electric Bicycle Scooter e-Bike Brushless DC Motor Controller 48V 60V 64V 1500W
Model 1500W. Energy 1500W. Material Aluminium. Battery Type Lithium Ion (Li-Ion). Compatible Bike Type E-Mountain Bike. Unit Type Unit. Unit Quantity 1. California Prop 65 Warning No.
1500W Sine Wave Control Electric Controller Low Noise Brushless Motor 48V -72V
Rated Power: 1500w. Do You Want to Experience a Smoother Ride?. It Has Low Noise and Stable Performance That Can Provide You with Strong Power. the Thicker Copper Wire Design Gives It Higher Inductance Accuracy, Making Your Electric Bike Start More Smoothly and Allowing You to Enjoy a More Comfortable Ride!
48V 60V 72V 1500W 3000W Brushless Controller 18mos 50A EBike Tricycle Motorcycle
MOS tube: 18mos. PAS(pedal assist). electric door lock. docking the two self-learning lines, the wheel will forward or reverse. if wheel forward ,Separate the self-learning line. if wheel reverse, Separate the self-learning line.
48V-72V Sine Wave Electric Motor Speed Controller 1500W For E-Bike Scooter
The 48V-72V Sine Wave Electric Motor Speed Controller 1500W is a universal controller designed for E-Bike scooters. Made of aluminum and weighing 0.65kg, this silver controller has an operating voltage range of 48V-72V and a current limit of 40±1A. It is compatible with various brands and bike types, providing a high rated power of 1500W. The controller also features a turnbuckle voltage of 1.1-4.2V and comes with a net weight of 0.5kg, making it a reliable choice for electric bicycle components.
Electric Bicycle Controller Kit 48V 1500W Conversion 2 Speed Mode
Electric Bicycle Controller Kit 48V 1500W Conversion 2 Speed Mode. Please see pictures of the item including pieces. Free shipping to lower 48 only
1500W Sine Wave Control Electric Controller Low Noise Brushless Motor 48V -72V
Rated Power: 1500w. Do You Want to Experience a Smoother Ride?. It Has Low Noise and Stable Performance That Can Provide You with Strong Power. the Thicker Copper Wire Design Gives It Higher Inductance Accuracy, Making Your Electric Bike Start More Smoothly and Allowing You to Enjoy a More Comfortable Ride!